|
|
Post by v8digou on Mar 10, 2012 2:16:46 GMT -4
well had enough of wheeling on my 33's time to upgrade!  so i got myself deuce  tore it down  striped down the rocks, i wasn't sure if i has a u joint front or not turns out...  ;D took the front and rear carriers out n had them welded  fabed up a "hat" for the four link  made some tabs  pulled the body off the blazer   rolled the frame in the garage  couldnt wait to cut all the ifs out, no turning back now lol  spring purches    the mud in the frame is never ending lol  and this is where i am at now, the weight is sitting on the coils its 54 inches to my arm on the bumper, i think those 44 inch army tires r gonna look sma  ll |
|
|
|
Post by v8digou on Mar 24, 2012 11:47:43 GMT -4
she a roller...the font and rearends are under it with tires the engine hood is gonna be just at 6 feet ;D ill get some pics up later on
|
|
|
|
Post by v8digou on Mar 27, 2012 15:10:17 GMT -4
|
|
|
|
Post by z28 on Mar 27, 2012 20:53:44 GMT -4
Ryan looks sweet.  what about them 33' 4 sale  |
|
|
|
Post by Charles on Mar 28, 2012 16:46:57 GMT -4
You still had to grind your yokes at your front output with the top loaders???.... they look like 1410's... how high is it? Looking good bye the way. Can't wait to see it. |
|
|
|
Post by v8digou on Mar 29, 2012 0:56:34 GMT -4
yeaim running a 241 case and it has a longer front output than the older cases, the front shaft is 1410 the top of my motor is 6ft off the ground lol, too high? lmao i never measured the top of the roof but the door handle is 70 inches...the botom of my front bumper is 50 inches...i need a step ladder!  |
|
|
|
Post by Charles on Mar 30, 2012 18:10:54 GMT -4
Looks awesome man!! Doesn't look like you turned your front pinion up at all when you made your spring pots. Could you turn that up a touch without messing up your caster too much?... or are you going to be fine where your at with the out put.
|
|
|
|
Post by chevyboy on Mar 30, 2012 20:17:35 GMT -4
Looking good so far!! What are you going to run for tires on the Blazer? I had to get a excavator in to put my body on the frame... ;D Keep up the good work!!
|
|
|
|
Post by v8digou on Mar 30, 2012 21:05:06 GMT -4
I can roll it up a touch with the links, belive it or not the shaft spins free with the grinding...most of my binding was at the case, yea the backhoe had to use the extend a boom to yet the body up high enough lol
|
|
|
|
Post by z28 on Apr 17, 2012 20:45:36 GMT -4
Ryan Any more though on them 33 |
|
|
|
Post by v8digou on Apr 18, 2012 16:34:36 GMT -4
there sold they went b4 i even started the swap
|
|
|
|
Post by z28 on Apr 18, 2012 19:37:10 GMT -4
thanks ryan  |
|
|
|
Post by Chevypower on Apr 19, 2012 9:38:47 GMT -4
So whats going on with this build any new progress pics anything? ?? |
|
|
|
Post by v8digou on Apr 19, 2012 20:28:12 GMT -4
yea i made some progress, got the hydro sterring all working, 4x4 shifter and clutch all done, redid some wiring, even had it down the 75 ft of driveway a few times, the front clip has to go on, finish some welds, ladder bars, still have to put my pinon brake on too, almost went out into traffic with her lmao
|
|
|
|
Post by Chevylover on Apr 20, 2012 12:28:36 GMT -4
Looking good !
|
|
what about them 33' 4 sale 
